news

Scientifically maintain the computerized flat knitting machine

Update:26-04-2020
Summary:

Computerized flat knitting machines are currently the m […]

Computerized flat knitting machines are currently the main production tool for sweater manufacturing. They are expensive, tens of thousands of cheap, hundreds of thousands of expensive. With the development and improvement of flat knitting machine technology, the cycle of use is also rapidly shortening. The system has been able to work for 5 years, and now the basic 3-year machine will be eliminated. Moreover, more and more people and manufacturers buy computerized flat knitting machines, and the profit of producing sweaters is getting lower and lower. The last scenario that may emerge when the computer is knitting is competing with the cost of electricity + rent + labor. If your knitting machine runs to win the cost, that is to earn.

How to scientifically maintain the computerized flat knitting machine is more important

Flat knitting machine head

First use cotton cloth to wipe the front and back covers and flyover of the machine head clean. To use an air gun and a vacuum cleaner to manually clean the cotton wool around the probe and the brush, you should be careful with your fingers to avoid accidents.

Body oil injection system

Pull the oil pump handle several times to ensure that the oil in the oil pump is always in the supply state.

Nose rail

First, use cotton cloth to clean the remaining grease and yarn scraps on the head rail, and use an oil-containing brush to inject the appropriate amount of lubricant into the head rail.

Traverse device

Apply grease to the drive screw evenly with a brush.

Drive System

Use the air gun and vacuum cleaner to align with the chariot wheel groove, main drive belt and its wheel base while blowing and sucking, and then wipe it clean with cotton cloth.

Electric control box

After opening the cover of the electrical box, use a vacuum cleaner to remove the dust and yarn from the cable board, at the same time clean the filter, and finally reset the electrical box cover; press the unpacking button of the side electrical box cover to open the side electrical box cover, Use a vacuum cleaner to remove the dust and yarn from the cable board, clean the filter at the same time, and finally reset the side electrical box cover.

Antenna creel

Use a brush and a vacuum cleaner to suck and clean the dust on the antenna stand, antenna bracket and alarm light, and clean it. You need to use a cotton cloth with a wax remover to clean the yarn tension disk on the antenna bracket; use a brush and a vacuum cleaner to Dust and yarn on the gauze table are sucked while brushing, then wipe clean with cotton cloth.

Yarn guide rod

Use cotton cloth to wipe off the dirt in the middle part of the yarn guide rod, then move the yarn feeder to the middle, and wipe it clean with cotton cloth; use an oily brush to add an appropriate amount of lubricant to the yarn guide rod, and then use cotton cloth to wipe off the lubricant Until a thin layer of lubricant film remains on the surface of the yarn guide rod.

Yarn clamping system

Use an air gun and a vacuum cleaner to clean the scissors clip, and further clean up the manual operation interface after booting.

Yarn feeder and side tension device

Pay attention to clean the yarn and wax marks on the yarn feeder and side tension device.

Needle bed and sinker headboard

Push the machine head and yarn feeder to the edge, use a special cloth knife to push all the needles of the front needle bed to the highest point, blow and suck with an air gun and vacuum cleaner, remove the needle bed and sinker bed, and then remove all The needles are reset, as are the rear needle bed and sinker bed. After repeating this twice, clean the front and rear needle beds and sinker beds with cotton cloth; pay attention to check whether all kinds of needles are all in place before restarting the machine, otherwise it will cause damage to the machine.

Stretching system

The main roller, open the main cloth, use needle-nose pliers to clean up the waste yarn, and use the oil-containing brush to inject a small amount of special oil into the mechanical transmission part to lubricate it.

Lift up the bottom plate, clean up the waste yarn from the bottom plate, and after cleaning, use oil-containing brush to inject a small amount of special oil into the bottom-up transmission device to lubricate it.

0
Views: 126